Skip to content
Thermoline Home
Carbon heating systems

Heating

Heat on demand — like from the sun

On this page you will find everything about heating with carbon: how the system works, what it costs and where its limits lie, the installation options in floors, walls and ceilings and as design panels – and the comparison with other heating systems, including approximate costs.

Heating reinvented

Carbon

Infrared surface heating – thin, silent, maintenance-free

Infrared heating systems in floors, walls or ceilings. Here you will find how the system works, what it is suited for, what it costs – and where its limits lie.

What problem does it solve?

Conventional heating needs a boiler room, pipes, radiators and regular servicing. In an existing building, new underfloor heating usually means new screed, dust and weeks of building work. And radiators mainly heat the air: warm air rises, while it stays cooler near the floor.

This is where the carbon heating system comes in. A heating surface just a few millimetres thin sits under the floor covering, on the wall or on the ceiling, is connected to 230 V and warms the surfaces in the room evenly – no boiler room, no pipes, no chimney.

How does the product work?

How does the product work?

The heating surfaces are printed all over with a patented carbon layer. When current flows, the layer heats up evenly across the whole surface and releases the heat mainly as infrared radiation – just as we know it from the sun. The surface is warm within minutes.

There are dedicated products for floors, walls and ceilings, each matched to where it is installed, plus design panels for walls or ceilings.

How the warmth spreads through the room

  1. Unheated room, the left wall is equipped with a carbon wall heating system.

    In the picture on the left you see an unheated room, whereby the left wall is equipped with a Carbon wall heating system.

  2. The wall heating, switched on, heats up evenly and transfers heat energy to the room.

    When switched on, the wall heats up evenly to the temperature set on the thermostat and transfers heat energy to all other walls, objects and people in the room.

  3. Walls, objects and people absorb heat and pass part of it on as secondary radiation.

    The walls, objects and people absorb some of this heat energy and at the same time pass on part of the received heat flow — this effect is called secondary radiation.

  4. All surfaces in the room have reached the same temperature, the heat equalisation current ceases.

    This is repeated until all walls, objects and the surface of people have the same temperature; only then does the heat equalisation current cease. The air itself is not directly heated.

How does infrared radiation heat a building?

Our infrared heating products have two features that fundamentally distinguish them from other types of heating. First, they are panel heating systems: floor, walls or ceiling heat the room without any radiator or other protruding components. Second, infrared radiation is used primarily to heat objects and not the air, as is the case with all convection-based heating systems.

If all the walls, the floor and the ceiling have the same temperature, we are warmed according to the principle of heat transfer. The second law of thermodynamics states that whenever two objects of different temperatures are near each other, there is a flow of heat from the warm to the cold object. This flow continues until the temperature levels have equalised. Humans perceive an ambient temperature of 20 to 22 degrees Celsius as very pleasant, since this also represents their surface temperature when dressed, so that virtually no heat exchange occurs.

Radiant heat and well-being

Radiant heat and well-being

Many people find radiant heat particularly pleasant: the surfaces in the room are warm, the air can be slightly cooler, and there is hardly any draught. Infrared heat has long been used in physiotherapy as well, for example for muscle tension.

Technical data at a glance

4–5 mm Build-up height Depending on the substrate, excluding floor covering or plaster.
approx. 105–115 W/m² Electrical output Floor approx. 115 W/m², wall approx. 105 W/m², ceiling 105–115 W/m².
230 V Connection Ceiling heating also available in low voltage, depending on the version.
Room by room Control Thermostat in each room, by app on the go if desired.

Which buildings and situations is it suited for?

  • New builds and renovations – including where no new screed is to be laid
  • Under parquet, tiles, laminate or vinyl, on the wall or on the ceiling
  • Timber and masonry construction – our references range from timber-frame houses to brick buildings
  • Older buildings and flats where a boiler room and pipes are missing or in the way
  • Individual rooms such as bathrooms, conservatories or offices that are to be heated separately

The system is most economical in a well-insulated building and combined with a photovoltaic system. How to prepare the building is explained under Insulation.

What are its advantages and limits?

  • Low build-up height of 4–5 mm – fits new builds and existing buildings
  • No boiler room, no pipes, no chimney
  • Maintenance-free – no filters, no chimney sweep
  • Fast response – warm surfaces within minutes
  • Every room can be controlled individually
  • Low investment compared with water-based systems
  • Ideal in combination with your own solar power

Limits – to be honest

  • Direct electric heating: one kilowatt hour of electricity becomes roughly one kilowatt hour of heat. A heat pump obtains several kilowatt hours of heat from one kilowatt hour of electricity. Running costs therefore depend heavily on the electricity price, insulation standard and room temperature.
  • Buildings with high heat demand – such as an uninsulated old building – use correspondingly more electricity; insulation should come first.
  • Hot water is not produced by the system; a boiler or a hot-water heat pump is needed for that.
  • Covered heating surfaces – large rugs, cupboards in front of wall heating – give off less heat.
  • Legal framework: whether direct electric heating is permitted and eligible for subsidies in a new build or when replacing a heating system depends on the building and the applicable rules (in Germany, among others, the Building Energy Act). We check this case by case.

Carbon or heat pump?

Both systems heat with electricity, but in different ways. A heat pump is more efficient per kilowatt hour of electricity, but costs considerably more to buy and needs servicing. The carbon system is inexpensive to buy, maintenance-free and very flat – it plays to its strengths in well-insulated buildings with low heat demand.

An example from our references: two detached houses built shortly after one another in Grabenstätt, measured in the same winter 2020/21. The house with carbon underfloor heating (KfW 55, 214 m²) used 44 kWh of heating electricity per m², the house with an air-to-water heat pump (KfW 39, 175 m²) 49 kWh per m². This compares two different houses and is not a standardised test – but it shows that the gap can be smaller in practice than expected. Investment and costs over 25 years are compared in the system comparison.

What does heating cost me per year?

The rule of thumb: heated area × consumption per m² × your electricity price. Measured values from reference buildings show how high consumption per m² is in practice. Example Neusiedl am See: 90 m² × 36.2 kWh/m² comes to around 3,260 kWh a year – at an assumed electricity price of €0.30/kWh, just under €980.

Property Building Heated area Measurement period Heating electricity per year Per m² and year Heating costs per reference sheet
Litzelsdorf (AT) Detached house, timber frame, new build 2020 109 m² 07/2020–06/2021 2,672 kWh 24.5 kWh €545
Litzelsdorf (AT) Detached house, new build 2018, with photovoltaics 178 m² one year (sheet dated Jan. 2020) 5,878 kWh 33 kWh €1,058 at €0.18/kWh; with own solar power €459
Neusiedl am See (AT) Flat, built 1955, renovated 2019, at least 24 °C 90 m² 07/2020–07/2021 3,259 kWh 36.2 kWh –
Lake Constance (DE) Detached house, new build, walls without external insulation, ceilings up to 4.5 m 220 m² 10/2018–10/2019 8,895 kWh 40.4 kWh –
Grabenstätt (DE) Detached house, new build 2018, KfW 55 214 m² 10/2020–06/2021 (heating season) 9,538 kWh 44 kWh –
St. Michael (AT) Old building c. 1900, uninsulated, carbon on ground floor only 53 m² 07/2019–06/2020 3,392 kWh 61.9 kWh €12.08 per m² at €0.195/kWh

Measured values from the manufacturer's reference sheets: heating electricity only, excluding household electricity and hot water. Costs only where the reference sheet states them, at the electricity price at the time. Consumption depends on insulation, room temperature and use. All references in detail: References.

What investment should you expect?

The investment depends on the area, where the system is installed and the floor build-up. As a guide:

  • Guide price: approx. €200 per m² including installation – for floor, wall and ceiling heating, depending on the installer.
  • Example house in the system comparison: around €20,000 for the carbon heating system – compared with €40,000 for oil heating and €55,000 for a heat pump (see table).
  • Reference Lake Constance, 220 m²: around €20,000 for the carbon underfloor heating; quotes for water-based systems were €30,000–40,000. Installed in 5 days by 2 tradespeople.
  • Design heating panels for individual rooms are available from €499.

We prepare a binding quote for your house after a short conversation.

What technical evidence and references are available?

  • Patented carbon coating – printed over the full surface for even heat across the whole area
  • Biophysical study by the Paul Sommer testing laboratory on the heating principle (see quote)
  • Measured consumption from occupied houses in Germany and Austria – all references
  • Brochure with all technical data to download
  • Electrical safety: heating foil type-tested by TÜV NORD CERT to DIN EN 60335-1 (certificate 44 780 24002601, valid until August 2029), CE-compliant under the Low Voltage Directive 2014/35/EU
  • Pollutants and emissions: SHI product passport (tested for pollutants, Sentinel Holding Institut) and emission test for VOC and formaldehyde by eco-INSTITUT
  • Electrosmog: certificate of the International Society for Electrosmog Research (IGEF)
  • Warranty: 20-year manufacturer's warranty

Information from the manufacturer IREWA (Carbon Heizsysteme GmbH, Rosenheim), with whom we work – IREWA website.

The heating principle of an infrared radiant heater corresponds to the principle of natural solar radiation, which health and the human organism also demand in their living space.

Study by the biophysical testing laboratory Paul Sommer

How do you get an individual quote?

Send us the living area, year of construction and – if available – the floor plan and energy certificate. We calculate investment, consumption and heating costs for your house, with photovoltaics if you wish.

Underfloor heating

Underfloor heating

The revolution in build height and efficiency

Neither a boiler room nor protruding objects — and depending on the floor covering, build-up heights of only 4 to 5 mm are possible.

Carbon heating foil laid under the floor covering.

Big strength, low build height

Depending on the floor covering, build-up heights of only 4 to 5 millimetres are possible — without the floor covering itself. Use your living space as you want, without compromises: this underfloor heating system requires neither a boiler room nor protruding objects and is completely silent.

At a glance

230 V Operating voltage No gas, no oil, no chimney.
approx. 115 W/m² Power draw The full-surface carbon coating converts electricity into heat almost without loss.
1–3 h/day Operating time On average over the year.

Why this underfloor heating

  • Invisible and silent – no boiler room, no protruding objects
  • Warm, dry surfaces – good for the indoor climate and the building fabric
  • Fast response – noticeably warm floor covering within minutes

Quick assembly, dust-free

Whether new build or renovation, whether parquet or tile — the installation is very clean and completed after just a few hours.

Applications and limits

Suitable for living rooms, bathrooms and kitchens in new builds and renovations – under parquet, laminate, vinyl or tiles, especially where every millimetre of build-up height counts.

Limits: the floor covering must be suitable for underfloor heating. Large rugs and furniture without legs reduce heat output from the covered area.

Wall heating

Wall heating

Insulation and heating in one

The special construction of heating panel, standing air layer and reflection layer does not only heat — it insulates at the same time.

Construction of the wall heating with heating panel, standing air layer and reflection layer.

Big strength, small thickness

Depending on the wall composition, installation depths of only 4 to 5 millimetres are possible — without plaster coating. The special construction using the patented heating panels in combination with a standing air layer and a reflection layer leads to a good insulating effect. The wall heating requires neither a boiler room nor protruding objects and operates completely without noise.

At a glance

230 V Operating voltage No gas, no oil, no chimney.
approx. 105 W/m² Power draw The full-surface carbon coating converts electricity into heat almost without loss.
approx. 30 % Operating time Of the day in winter.

Why this wall heating

  • Invisible and silent — no boiler room, no protruding objects
  • Insulating effect through standing air layer and reflection layer
  • Responsive — noticeable heat within minutes

Quick assembly, dust-free

Whether new build or renovation — the installation of the wall heating is similar to a drywall installation and is completed after just a few hours.

Applications and limits

Suitable for external and internal walls in new and old buildings, including where the floor is to be left untouched. Installation is similar to drywall construction.

Limits: the heating surface should not be blocked by cupboards. Check the layout plan before drilling into a heated wall.

Ceiling heating

Ceiling heating

Natural warmth from above

Warmth from above is the normal case in nature. The ceiling heating takes that up: it radiates downwards, without a boiler room and without noise.

Construction of the ceiling heating, similar to a drywall construction.

Big strength, small thickness

Depending on the ceiling composition, installation depths of only 4 to 5 millimetres are possible — without plaster coating. Use your living space as you wish: the ceiling heating requires neither a boiler room nor protruding objects and is completely silent.

At a glance

22–230 V Operating voltage Depending on the version also in low voltage.
105–115 W/m² Power draw The full-surface carbon coating converts electricity into heat almost without loss.
approx. 30 % Operating time Of the day in winter.

Why this ceiling heating

  • Invisible and silent – no boiler room, no protruding objects
  • Warm, dry surfaces – good for the indoor climate and the building fabric
  • Fast response – noticeable warmth within minutes

Quick assembly, dust-free

Whether new build or renovation — the installation of the ceiling heating is similar to a drywall installation and is completed after just a few hours.

Applications and limits

Suitable for rooms in which the floor and walls are to remain free – such as offices, bathrooms or attic rooms – and for renovations without work on the floor.

Limits: in very high rooms the output needs particularly careful planning. Ceiling lights and recessed spots are left out when laying.

Installation

Design heating panels

Heating panels

Quick and easy to install

A panel on the wall or under the ceiling — no pipes, no maintenance, no fire hazard. On request with integrated spotlights.

Big strength, small thickness

Big strength, small thickness

Depending on the wall properties, installation depths of only 4 to 5 millimetres are possible — without plaster coating. The heating panels require neither a boiler room nor protruding objects and are completely silent. The infrared coating converts electricity into heat with almost no loss and provides noticeable warmth within minutes.

At a glance

230 V Operating voltage Simply connect – no pipes, no chimney.
from €499 Purchase price Low purchase costs, quick and easy to install.
max. 37 °C Surface temperature Low temperature – child-friendly, no risk of burns.

Advantages of the design heating panels

  • Quick and easy installation
  • Long service life and maintenance-free
  • No leaks, no freezing, no open flame
  • Low temperature up to max. 37 °C – child-friendly
  • No dirt, no emissions in the room
  • No noticeable draught, hardly any dust stirred up
  • Space-saving – replaces a radiator
  • Simple remote control
  • Optional indirect lighting and integrated spotlights
  • Particularly climate-friendly when run on green electricity or your own solar power

Quick assembly, dust-free

The panel is fixed to the wall or ceiling and connected — that is all it takes. No screed, no drywall, no dust.

Applications and limits

Suitable for individual rooms, to replace or supplement a radiator, in bathrooms, offices or for retrofitting without any building work.

Limits: a panel is a limited heating surface. Whether panels alone can heat an entire house can only be determined by a heating load calculation.

Panels in use

Water heating and electric heating

Comparison

The comparison with other heating systems

While infrared heating heats everything except the air, the opposite happens with convection-based heating — with consequences few people are aware of.

The big difference between infrared heating and conventional convection-based heating lies in how the heat is distributed. Infrared heating mainly warms surfaces, objects and people; convection-based heating mainly warms the air.

A radiator heats the air in contact with it. The air rises to the ceiling, cools on its way to the opposite wall, sinks to the floor and flows back to the radiator. This creates air circulation that heats the room air – convection. The system is proven and widespread; even so, some of its characteristics are worth knowing when you compare.

System comparison: investment and costs over 25 years

Four options for the same example house – from conventional facade insulation with oil heating to the carbon heating system with reflective insulation and Thermoline paints.

Comparison Conventional insulation (ETICS) + oil heating Conventional insulation (ETICS) + heat pump Conventional insulation (ETICS) + carbon heating system Carbon heating system + ISOFOLIE reflective insulation + Thermoline paints
Heating water-based with oil burner, convective heating (warm air) water-based with heat pump, convective heating (warm air) surface heating with carbon system, floor and/or wall surface heating with carbon system, floor and/or wall
Construction 20 cm conventional facade insulation, triple glazing, 30 cm roof insulation 20 cm conventional facade insulation, triple glazing, 30 cm roof insulation 20 cm conventional facade insulation, triple glazing, 30 cm roof insulation, without PV system (own power generation) ISOFOLIE reflective insulation on the inside of the external wall and in the roof, Thermoline paints inside and outside for moisture regulation, without PV system
Investment in heating €40,000 €55,000 €20,000 €20,000
Investment in roof and wall insulation €105,000 €105,000 €105,000 €75,000
Primary energy demand of insulation up to 350 kWh/m² up to 350 kWh/m² up to 350 kWh/m² up to 7 kWh/m²
CO₂ reduction no no no yes
Heat demand per year 12,000 kWh 6,000 kWh 3,600 kWh 2,900 kWh
Cooling load / solar reflection no no no yes
Running costs per year €4,500 €4,000 €1,800 €1,500
Room air temperature 23 °C 23 °C 20 °C 18 °C
Ventilation system yes yes no no
Service life of heating system 20 years 20 years 50 years and more 50 years and more
Total costs over 25 years €115,000 €100,000 €45,000 €38,000
Total cost saving compared with oil heating – −13 % −60 % −67 %

Example calculation by Thermoline Home for a detached house; manufacturer's figures. Running costs per year including servicing, chimney sweep and a provision over 20 years, excluding repairs. Total costs over 25 years without price increases and without CO₂ pricing. "Primary energy demand of insulation" refers to the energy used to manufacture the insulation material. We calculate the figures for your house individually.

Water heating

Room climate

Room climate

When air is heated, its relative humidity drops. Many people find dry heating air in winter unpleasant, for example on the skin and mucous membranes.

House dust allergy

House dust allergy

Air circulation also distributes house dust around the room. For people with a house dust allergy, this can be an additional burden during the heating season.

Mould

Mould

When humid, warm room air meets a cold wall surface, moisture can condense there. If the spot stays damp for a long time, conditions become favourable for mould. Warm wall surfaces – as with surface heating – reduce this risk.

Ventilation

Ventilation

Air heating brings heat into the room via the room air. Regular ventilation is needed for a good indoor climate, and part of the heat is lost with the warm air. With surface heating, more heat remains stored in walls and objects.

Maintenance and repair

Maintenance and repair

Such heating systems require annual maintenance, for example to replace clogged filters, plus a visit from the chimney sweep. Possible repairs due to wear and tear come on top. Annual maintenance costs remain.

Electric heating

Electric underfloor heating

Electric underfloor heating

With conventional electric underfloor heating, a heating wire lies under the floor covering, similar to the pipes of water-based underfloor heating. The wire gets very hot at specific points and first has to spread the heat through the floor build-up. A full-surface carbon layer, by contrast, warms the entire area evenly at a low surface temperature.

Thermoline Home

Advantages

Six reasons for surface heating

No radiator, no boiler room, no maintenance — and an efficiency significantly higher than that of all other heating systems on the market.

up to 96 % Efficiency Electricity is converted almost entirely into heat.
0 Services No chimney sweep, no filters, no annual bill.
Minutes Response time The surface warms up quickly and switches off immediately when the sun shines.
Neither radiator nor boiler room

Neither radiator nor boiler room

Use your entire living and usable space as you wish. Let your creativity run free when it comes to furnishing.

Maintenance-free

Maintenance-free

The use of only high-quality materials and the simple construction of these heating solutions mean that maintenance is completely unnecessary.

High efficiency

High efficiency

The carbon layer applied over the full surface releases heat evenly into the room and converts electricity almost entirely into heat – according to the manufacturer with an efficiency of up to 96 %. How much electricity a house needs overall depends on its heat demand; the system comparison and the measured heating costs give examples.

Investment and energy calculation

Example: single-family house, 150 m² living space, KfW 55 standard. We will work out the comparison for your house — investment, operating costs and payback, with and without photovoltaics.

Arrange an introductory call

We look at your house, work through the comparison and tell you which building blocks pay off in your case — and which do not.