Skip to content
Thermoline Home
Thermoline colours

Colours

Around 50 % of the dry substance is glass

Thermoline is available for inside and outside: Interieur for walls and ceilings, Exterieur for the façade. Microscopically small glass beads enlarge the surface, absorb moisture and release it more quickly. A paint does not replace thermal insulation — it keeps walls dry and easier to heat.

Why glass in the paint?

A wall that has stored moisture is difficult to heat — water conducts heat about twenty-five times better than air and carries it out of the component. The hollow glass bodies in Thermoline increase the moisture-absorbing surface of the paint by 30 to 40 times. Moisture is absorbed faster and released faster, the component stays dry — and a dry component can be heated.

Important to keep in mind: Thermoline is not thermal insulation. The paint hardly changes the heat transfer through a wall; it works through dry surfaces, more even surface temperatures and — outside — solar heat gain. Where thermal protection is lacking, suitable insulation helps: Insulation reconsidered.

Thermoline Interieur

Interior

Helps save heating cost

Measured 10 to 15 % lower heating costs, surfaces up to 3 °C warmer — and free of biocides, preservatives and nanotechnology.

What problem does it solve?

Walls and ceilings constantly absorb moisture from the indoor air — from cooking, showering and breathing. Conventional interior paints let this moisture penetrate the plaster and the building fabric, where it is released only slowly and with a lot of heating and ventilation energy.

The result is cool wall surfaces, an uncomfortable room and a hand on the thermostat: to feel comfortable, the air is heated more than necessary. Damp, cool walls are also the breeding ground for mould.

Section through a wall: the glass beads in the paint layer enlarge the surface, moisture is released faster.

How does the product work?

Thermoline Interieur has a high proportion of microscopically small glass beads, which make up about 50 % of the dry substance. In the interior of the house they increase the moisture-absorbing surface of the paint on walls, ceilings and roof slopes by 30 to 40 times. This reduces the entry of moisture from the room air into the deeper building substance and results in faster, better and more demand-oriented drying.

The rapid regulation of room air humidity that takes place in this way also achieves quickly perceptible comfort in the room. Ventilation heat losses are avoided.

10–15 % measured heating cost savings Climate-adjusted measurements over several heating seasons, checked by independent specialist firms according to the manufacturer. How we calculated this
+ 3 °C surface temperature Up to — on walls, ceilings and sloping ceilings, according to the manufacturer. How we calculated this
4 m²/l coverage Tested to DIN EN 13300 (MPA Braunschweig). How we calculated this
20,000+ colours Can be mixed to KEIM, NCS and RAL.

The explanatory video

Which buildings and applications is it suitable for?

Thermoline Interieur is an interior paint for walls, ceilings and sloping ceilings in living spaces — in new builds and renovations alike. It is designed for normal residential moisture loads.

  • Substrates: load-bearing, clean and dry. Adhesion was tested on chipboard, woodchip wallpaper, foil and galvanised steel — in every case with the best possible rating of 0.
  • Before painting: clarify the causes of existing moisture (e.g. rising damp or leaks). The paint does not replace remediation.
  • Application: colour, primer and coating build-up are matched to the property; consumption, drying and application temperature according to the current data sheet.
  • Not for façades: for exteriors there is Thermoline Exterieur.

What are its advantages and limits?

  • enables better heating of walls due to the glass surface
  • improves comfort, indoor climate and health well-being
  • reduces convection
  • creates even surface temperatures
  • creates even temperatures in the room
  • improves energy use
  • heating cost savings: measured 10 to 15 %, up to 25 % according to the manufacturer
  • improves the exchange of heat radiation
  • improves the absorption of solar energy even with low radiation
  • improves heat transfer to substrates that can store heat
  • noticeably faster heating-up – our own experience in our house in San Fulgencio with ISOFOLIE® and carbon underfloor heating (case study Spain under References)
  • regulates building component humidity and room air humidity
  • reduces the risk of mould — without biocides
  • protects the building fabric
  • reduces air pollutants that diffuse out of the building
  • is free of pollutants and toxins
  • does not pollute the environment
  • is available in over 20,000 colour variations

The limits

  • Not thermal insulation. Thermoline Interieur hardly changes the heat transfer through the wall. It works through drier surfaces, more even surface temperatures and radiant heat exchange in the room. Where a component lacks thermal protection, suitable insulation is needed — see Insulation reconsidered.
  • No substitute for ventilation. Moisture absorbed by the surface still has to be aired out.
  • Savings depend on the building. Construction, heating system and heating habits determine how much can actually be saved.
  • Fix moisture damage first. No paint helps against rising or penetrating damp.

What investment can you roughly expect?

With an interior paint job, only a small part of the cost is the paint itself: labour, preparing the substrate and setting up the site make up the larger part. The amount of material can be estimated from the coverage — around 4 m² per litre.

Guide price: approx. €15 per m², depending on the painter. The exact cost of Thermoline Interieur for your property depends on area, substrate and colour – we will give you the price in our quote.

What technical evidence and references are available?

Thermoline Interieur carries the Austrian Ecolabel UZ 17. According to the manufacturer, climate-adjusted measurements over several heating seasons showed heating cost savings of 10 to 15 %, checked by independent specialist firms. The key test results:

Property Test Result Testing institute
Coverage DIN EN 13300 4 m²/litre MPA Braunschweig
Hiding power DIN EN 13300 Class 1 MPA Braunschweig
Wet abrasion resistance DIN EN 13300 Class 2, scrub-resistant MPA Braunschweig
Water absorption DIN 52617 0.045 kg/(m²·h^0.5) MPA Braunschweig
Water vapour permeability DIN EN ISO 12572 / DIN 52615 sd dry 0.45 m · damp 0.16 m MPA Braunschweig
Solar reflectance DIN EN 410 0.82–0.83 (also after 8 years of ageing) ZAE Bayern
Fire behaviour DIN 4102 Part 1 B2 MPA Braunschweig
Adhesion to substrate ÖNORM EN ISO 2409 Rating 0 (best possible) OFI Austria
Organic solvents / aromatics UZ 17 < 200 ppm / < 5 ppm OFI Austria
Formaldehyde UZ 17 < 10 ppm Analytik GmbH
Hygiene HK/B/1679/01/2002 passed PZH N.I.O. Hygiene

Source: test certificates and product information from the manufacturer EC Economic Colors (thermoline-farben.de), as of October 2026. The current technical data sheet and safety data sheet are binding.

How do you get an individual quote?

Tell us which rooms are involved and what bothers you — cold walls, damp, mould or high heating costs. We check the substrate and the moisture situation and prepare a quote for material and application.

Thermoline Exterieur

Exterior

The intelligent skin for your house

Less moisture absorption, better dehumidification, higher solar input into storable substrates — even with diffuse radiation.

What problem does it solve?

A façade is exposed to the weather: driving rain, dew and the humid outside air constantly take their toll. Conventional façade paints become brittle over time, develop micro-cracks and then absorb moisture. According to the manufacturer, just 4 % moisture above the base moisture level is enough to reduce the insulating performance of an external wall by around half — a damp wall conducts heat to the outside.

On top of that come dirt and algae. The façade needs repainting more often, and the external wall cools down more in winter.

Section through a façade: solar energy penetrates the paint layer and is stored in the masonry.

How does the product work?

On a façade or masonry, less moisture absorption and better dehumidification are achieved, and optimal insulating properties are restored. At the same time, a higher solar input into storable substrates is made possible, even with diffuse radiation.

The heating energy demand of a building depends on the thermal sensation of its occupants. If a person feels comfortable and at ease, the so-called feel-good temperature has been reached. The best, quickest and cheapest way to achieve this is not through warm room air, but through the radiation of warm walls.

Summer and winter, two directions

As with Thermoline Interieur, 50 % of the dry substance of the paint consists of microscopically small hollow glass particles. Through this structure, solar energy can penetrate and be stored in massive building components and materials. The result is measurable: the temperature on the inside of the building’s exterior walls increases by up to 1.5 degrees Celsius. This leads to a dry and warm wall and thus to significant savings in heating energy.

In summer, on the other hand, the reverse vapour pressure gradient takes effect. The vapour pressure increases inwards, which results in better evaporation of moisture and a cooling effect on the inside of the outer wall.

On insulated façades, for example with external thermal insulation composite systems, no solar heat reaches the masonry — the insulation layer sits in front of it. There, Thermoline Exterieur works mainly as surface protection: the surface stays drier and is less prone to dirt and algae. According to the manufacturer, renovation intervals can be extended by up to 100 %.

Thermography: Thermoline on the left, conventional façade paint on the right

Thermographic image of a test specimen coated with Thermoline Exterieur: the stored heat is visible as a warm hue.
Thermographic image of a test specimen with conventional façade paint: the substrate is noticeably colder.

Thermographic images after the test setup with homogeneous masonry units. The right side of the two test specimens was coated with normal façade paint on normal façade plaster: the substrate absorbs very little energy and cools down very quickly. The left side was coated with Thermoline Exterieur. During the day the substrate absorbs solar energy and heat radiation much better; the heat is stored in the building structure and can be slowly released again during the night.

+ 1.5 °C on the inside of the external wall Up to — on solid walls with storage capacity, according to the manufacturer. How we calculated this
up to 100 % longer renovation intervals According to the manufacturer; depends on substrate, weathering and initial condition. How we calculated this
approx. 3 m²/l coverage On a smooth surface with two coats (DIN EN 13300). How we calculated this

The explanatory video

Which buildings and applications is it suitable for?

Thermoline Exterieur is a façade paint for new builds and renovations.

  • Substrates: new and old render, concrete and suitable, intact old coatings. The product information also lists external insulation systems, wood, metal and plastic. Suitability, primer and compatibility are checked for every substrate.
  • The solar effect only applies to solid walls with storage capacity — brick, natural stone, concrete. On insulated façades, surface protection is the main benefit.
  • Preparation: the substrate must be dry, clean and load-bearing; absorbent renders are primed, crumbling areas renewed.

Application at a glance

Feature Guide value
Application roller, brush or airless
Build-up two coats
Total film thickness 0.18 mm
Thinning first coat max. 5 % water
Application temperature +5 to +30 °C (air, material and substrate)
Drying approx. 2–3 hours per coat
Coverage approx. 3 m²/l on a smooth surface with two coats
Storage cool, dry, frost-free; 24 months

Guide values from the manufacturer’s product information (thermoline-farben.de). Substrate and weather affect consumption and drying; the current technical data sheet is binding.

What are its advantages and limits?

  • dries faster thanks to the enlarged surface
  • water- and dirt-repellent
  • prevents dirt and algae without biocides
  • counteracts rapid embrittlement
  • lets solar heat into substrates with storage capacity — even with diffuse radiation
  • up to 1.5 °C warmer inside surface of solid external walls
  • renovation intervals up to 100 % longer according to the manufacturer
  • high solar reflectance, tested even after 8 years of ageing
  • vapour-permeable
  • over 20,000 colours to KEIM, NCS and RAL

The limits

  • Not thermal insulation. Thermoline Exterieur does not replace insulation and changes the heat transfer through the wall only indirectly — through a drier wall and solar gain. How conventional insulation and reflective systems compare is shown in Insulation reconsidered.
  • Solar effect only on solid walls. On insulated façades and lightweight constructions, surface protection remains.
  • The effect depends on the property. Substrate, orientation, weathering and initial condition determine how much is achieved.
  • Fix moisture damage first. Penetrating or rising damp must be remedied before painting.

What investment can you roughly expect?

As with interior painting, the cost of a façade renovation is driven mainly by scaffolding, preparation and labour rather than by the paint. A long-lasting coating therefore pays off over the years: if the façade needs repainting less often, scaffolding and labour are needed less often too. Material consumption is around 3 m² per litre for two coats.

Guide price: approx. €15 per m² of façade, depending on the painter. We will give you the exact price for your property in our quote.

What technical evidence and references are available?

Thermoline Exterieur has been tested at MPA Braunschweig and ZAE Bayern, among others. The key results:

Property Test Result Testing institute
Coverage DIN EN 13300 approx. 3 m²/litre MPA Braunschweig
Hiding power DIN EN 13300 Class 1 MPA Braunschweig
Wet abrasion resistance DIN EN 13300 Class 2, scrub-resistant MPA Braunschweig
Water absorption DIN 52617 0.053 kg/(m²·h^0.5) · silicone variant 0.023 MPA Braunschweig, MA 39 Vienna
Water vapour permeability DIN EN ISO 12572 / DIN 52615 sd dry 1.73 m · damp 0.35 m · silicone variant 0.02 m MPA Braunschweig, MA 39 Vienna
Adhesive tensile strength DIN EN ISO 4624 render 0.58 N/mm² · concrete 0.79 N/mm² MPA Braunschweig
Solar reflectance DIN EN 410 0.82–0.83 (also after 8 years of ageing) ZAE Bayern
Fire behaviour DIN 4102 Part 1 B2 MPA Braunschweig
Hygiene HK/B/1679/01/2002 passed PZH N.I.O. Hygiene

Source: test certificates and product information from the manufacturer EC Economic Colors (thermoline-farben.de), as of October 2026. The current technical data sheet and safety data sheet are binding.

How do you get an individual quote?

Tell us about the façade — year of construction, wall build-up, condition and orientation. We check the substrate and prepare a quote for material and application.

Arrange an introductory call

We look at your house, work through the comparison and tell you which building blocks pay off in your case — and which do not.